Search results

Could this reaper because of a bad battery. I know that when I had to tow the car to a repair shop, we used the warning signals on the car, and after 7 km the battery was empty. So I know that the battery may not be the best.

This is the fault codes. Full scan. Address 01: Engine Labels: 036-906-034-APE.lbl Part No: 036 906 034 CA Component: MARELLI 4MV 4637 Coding: 00051 Shop #: WSC 00046 VCID: 53AF64CFA11F17DE67-4B64 WAUZZZ8Z73N006323 AUZ7Z0B2128047 2 Faults Found: 17989 -...

Here is all the lights. :)

I celebrated to soon. I used the car yesterday in the worst time of the day, and the car suddenly stalled and all the lights in the dashboard come on. This is the fault message i get. 2 Faults Found: 17989 - Throttle Actuator (J338) P1581 - 35-00 - Basic Setting Not Performed...

I removed the brass and tapped the hole and put a bolt with some fitting tape on in the hole. So it's all sealed up.

Adaptation did not work at first. Got the error message. But after reading I tried again, now with some more juice on the battery, and the coolant temp at 80. And that did it. So now the car works again. Thanks for all the help! :D

Audi dealership in Norway are ripoff. So I rather order online thirdparty parts.

Thanks, I will try to block that one out. That should not be to hard. Is it possible to do the adaptation without vcds. Some say that it will learn by it self. I don't have vcds, so I guess this will cost another £100-200 at an workshop.

Thanks for the fast reply. The part number for the defect one is 036 133 062 N and the part number the Audi dealer ment was the right on is 036 133 062 L. If I bought the part from my Audi dealer it was £1000,- and from Europart £260,- :oops:

Hi I have a Audi A2 1,4 Petrol 2002. The throttle body is not working and the repair shop estimated the repair to be £1500,- I will fix it but the dealer gave me the right part number, but the part is not the same. I don't know if it is a vacuumed line? Can I block the hole and use it? Regards...

Sorry for the late answer Rosstbeef, I don't get notifications when I have received new messages so I must look at that. We changed the camshaft at the top of the engine. No more fault messages but there is a knocking noise, witch the mechanic says is the knock sensor that is not tighten...

New update and finally everything works great. I have had the car with an mechanic and this is the worst case he has ever worked with. We have changed almost every sensor in the car but that dit not fix the misfire problem. There was also a lack of compression on cylinder 2. So thought that he...

Yes is has been frustrating. Especially since I bought this car for my wife. We have owned the car for almost two years and she has stil not used it. I gave £2300,- for the car and have used more then £2700,- on parts and labor. I'm lucky that most of the repairs has been done by a friend of...

I first replaced one ecu and the new mechanic replaced another one, with the latest firmware. So that should not be the problem. He said that old firmware could cause a problem, but he has upgraded mine, so it must be something else. We did not exchange the cam housing, camshaft or roller...

Yes is seems like it is the same fault. The idle on mine is much better after I purchased a new overhauled head. We also bought 8 new valves. A new piston and rings on cylinder 2. I rode the car 40 km and it worked just fine. But when I stopped and let the car idle for 1 min, the engine error...

Hi Rosstbeef. My car has been with a car mechanic for 4 month now. The valves was sometimes stuck so he bought a refurbished top. I got the car back on Friday. But when I came home and let the car idle the engine lamp came on. I used VCDS and it was missfire cylinder 2 once more. I beginning...

Now we have ordered a new camshaft and will try to change that. It was worn so it could be that, but another friend said that it would not give me a misfire cylinder two error. It could be that the top of the engine has an crack, because when the engine is cold it works fine, but when it gets...

I was not happy for long. It seems like the car don't like to come to a new home. After we change the throttle house I was backing up the car and due to the erratic idle I manage to stall the car and then the engine light began to flash. Now I got the message that it was misfire cylinder 2. I...

I had misfire cylinder 2. The problem with my car was that there was a leak from one of the valves on cylinder two. We got some new seals and changed the seals on all 16 valves. Then we cleared the fault codes and no more misfire.

I have no misfire on cylinder two anymore. I delivered the car to a Polish car mechanic and he have had my car for a week and he called me today and said that my car was fixed. It was the throttle house. He ordered a new one and changed it. He have ordered another one also because the idle is a...