Thanks for all your help Ian!Cathy, this is Ian from FB. I'm sure Paul will have stock, if you need any help with it I am based near Heathrow, not too far from you I believe.
Ian
Thanks for all your help Ian!Cathy, this is Ian from FB. I'm sure Paul will have stock, if you need any help with it I am based near Heathrow, not too far from you I believe.
Ian
Probably a long shot, but are these still available?
Hi Paul,
I've just come across the OSS thread. I have a non functioning OSS which packed up about two years ago. I had almost written off any prospect of getting it repaired. From memory, the problem occurred when I had opened the roof on a very hot day, on trying to close it, I got an awful noise as the motor struggled to close it. With a bit of manual help, I managed to get it closed. I think your mod may provide a solution to getting it working again.
Question is, do you have parts available please and how difficult is the fitting. I shudder at the prospect of headlining removal and wouldn't know where to start.
I don’t have any motor mounts left. I would consider making another batch in the future if there was enough interest
A member may well contact you offering you one that I sold him from the original batch. His A2 was stolen before he could fit the motor mount
It is a doable diy job to fit the motor mount through the light cluster hole in the headlining but you do need a dremmel with a 90 deg angle head and cutting discs to remove the original mount
Cheers. Paul
Sent from my iPhone using Tapatalk
Price is £140 delivered in the UK if you get in on the first or second batch, it will be more expensive after the initial two batches, as I envisable having to set up to make one or two after the initial batches, and this is far more time consuming
Thanks for kicking this off Tom,
Number one for Tom @timmus PAID
retained at whittle towers
Number two for Tom @2work PM sent
Number three for Erling @Erlingtheelder PAID and received
Number four is for Stefan @steaman PAID and received
Number five is for Robin @Robin_Cox PAID retained at whittle towers
Number six is for James @Wingz123 PM sent
Number seven is for @TYP 8Z PAID & received
Number eight is for @Weetank2 PAID Posted
Number nine is for Nod @nod PAID. posted
Number ten is for @fhl PAID & received
Number 11 is for Andy @Sidewinder PAID Received
Number 12 is for @Jellybean PAID Received
Number 13 is for @daneneeliz PM sent
Number 14 is for @Walkersman Interest withdrawn
Number 15 is for @Catnip64 PAID Delivered
Number 16 is for @Tom_89 PM sent
Number 17 is for @wilco184 PM sent deferred
Number 17a is for @Kleynie. PAID and posted 22 feb 2021 delivered
Number 18 is for @Nick Interest withdrawn
Number 19 is for @Saile PAID Posted
Number 20 is for @longdog PAID Posted
Number 21 is for @Louis PAID Delivered
Number 22 is for @Kleynie PM sent
Number 23 is for @PeterM PAID and received
Number 24 is for @Woodsey65 PM sent
Number 25, 26, 27, 28, 29 are for @Kleynie PAID Received
Number 30 & 31 are for @ajsellors PAID Received
Number 32 & 33 are for @ecurb PM sent
Number 34 is for @BiggDogg PM Received
Number 35 is for @MrDCG PM Posted
If you remove the motor and try to move each cable with a flat screwdriver you may get an idea if the cable has become broken at the other end. If the cables move but do not move the roof panel then they have become detached and the whole roof needs to come out for a repair.Hello --- your detailed post re open sky roof problem is of interest to me . I have a 2004 late model 1.6 with 40,000 miles a good car with sat nav added , cruise control etc, but roof just started to fail. opening and closing ( just ) its pulling to one side and making noised and jamming, after a few goes I managed to close it. A fellow menber on the club says my problem is what you have posted here ? I will try to remove moter and look inside in next few days, if I can see an obvious issue I would be very interested in your new machined motor mount. You perhaps will have a view as to if my problem is likely to be motor mount ?
Thanks
Richard Hosking
Price is £140 delivered in the UK if you get in on the first or second batch, it will be more expensive after the initial two batches, as I envisable having to set up to make one or two after the initial batches, and this is far more time consuming
Thanks for kicking this off Tom,
Number one for Tom @timmus PAID
retained at whittle towers
Number two for Tom @2work PM sent
Number three for Erling @Erlingtheelder PAID and received
Number four is for Stefan @steaman PAID and received
Number five is for Robin @Robin_Cox PAID retained at whittle towers
Number six is for James @Wingz123 PM sent
Number seven is for @TYP 8Z PAID & received
Number eight is for @Weetank2 PAID Posted
Number nine is for Nod @nod PAID. posted
Number ten is for @fhl PAID & received
Number 11 is for Andy @Sidewinder PAID Received
Number 12 is for @Jellybean PAID Received
Number 13 is for @daneneeliz PM sent
Number 14 is for @Walkersman Interest withdrawn
Number 15 is for @Catnip64 PAID Delivered
Number 16 is for @Tom_89 PM sent
Number 17 is for @wilco184 PM sent deferred
Number 17a is for @Kleynie. PAID and posted 22 feb 2021 delivered
Number 18 is for @Nick Interest withdrawn
Number 19 is for @Saile PAID Posted
Number 20 is for @longdog PAID Posted
Number 21 is for @Louis PAID Delivered
Number 22 is for @Kleynie PM sent
Number 23 is for @PeterM PAID and received
Number 24 is for @Woodsey65 PM sent
Number 25, 26, 27, 28, 29 are for @Kleynie PAID Received
Number 30 & 31 are for @ajsellors PAID Received
Number 32 & 33 are for @ecurb PM sent
Number 34 is for @BiggDogg PM Received
Number 35 is for @MrDCG PM Posted
Price is £140 delivered in the UK if you get in on the first or second batch, it will be more expensive after the initial two batches, as I envisable having to set up to make one or two after the initial batches, and this is far more time consuming
Thanks for kicking this off Tom,
Number one for Tom @timmus PAID
retained at whittle towers
Number two for Tom @2work PM sent
Number three for Erling @Erlingtheelder PAID and received
Number four is for Stefan @steaman PAID and received
Number five is for Robin @Robin_Cox PAID retained at whittle towers
Number six is for James @Wingz123 PM sent
Number seven is for @TYP 8Z PAID & received
Number eight is for @Weetank2 PAID Posted
Number nine is for Nod @nod PAID. posted
Number ten is for @fhl PAID & received
Number 11 is for Andy @Sidewinder PAID Received
Number 12 is for @Jellybean PAID Received
Number 13 is for @daneneeliz PM sent
Number 14 is for @Walkersman Interest withdrawn
Number 15 is for @Catnip64 PAID Delivered
Number 16 is for @Tom_89 PM sent
Number 17 is for @wilco184 PM sent deferred
Number 17a is for @Kleynie. PAID and posted 22 feb 2021 delivered
Number 18 is for @Nick Interest withdrawn
Number 19 is for @Saile PAID Posted
Number 20 is for @longdog PAID Posted
Number 21 is for @Louis PAID Delivered
Number 22 is for @Kleynie PM sent
Number 23 is for @PeterM PAID and received
Number 24 is for @Woodsey65 PM sent
Number 25, 26, 27, 28, 29 are for @Kleynie PAID Received
Number 30 & 31 are for @ajsellors PAID Received
Number 32 & 33 are for @ecurb PM sent
Number 34 is for @BiggDogg PM Received
Number 35 is for @MrDCG PM Posted
Hi Paul, wow that is an amazing peice of engineering, I would absolutely love to order one as my sky roof just broke in the open position lol. Many thanks kind regards Ianhere are the rest of the pictures, showing the final assemble attached to the OSS panel
View attachment 75677
Motor mount assembled to the cable guide tubes
View attachment 75678
Old and then new motor mount
View attachment 75679
top and bottom halves of the new motor mount
View attachment 75680
I would consider manufacturing these for members, but there is a lot of machining time and two pieces of aluminium plate involved and therefore they will not be costing pennies. I still need to work out the cost to manufacture as the first one made involved a lot of tweakes to the Gcode and the second one made still needed some slight adjustments and therefore I do not have representative machine times.
I intend to make another one at the weekend and will hopefully have no changes to make now to the Gcode and as such I can get representative times.
It will be cheaper if a production run is done as its quicker to make say 5 tops, then 5 bottomes, than to make them one at a time as there is only one machine set up per set
If you are interested in one of these then please post on this thread, no commitment at this time just showing your potential interest, this will give me an idea of numbers for a batch and therefore a price.
Simple scenario is the larger the run the cheaper will be the price
Cheers,
Paul